Tuesday, August 6, 2013

VS Voice


A bit more prodding and pummeling and for a bit of a laugh I loaded up a sample from the Sequential Circuits VS Synthesizer. This is allegedly waveform #20 from the wavetable. I have no idea if it is correct or not but there is an interesting interview with one of the chaps, Chris Mayer, that helped designed the VS and he mentioned that he wanted the interpolated sound of a short samples. Worked out that I can get all of the factory waveforms of the VS into one 48pin QFP... Thinking maybe a 7 segment display and a digital pot to choose the waveforms. Could do the joystick thing... could also do two control voltages for up/down and left/right. Might just start out with two waveform selections and a digital mix and see how we go from there...

sin(sin(x))


Well into a little bit of DX VCO... The DAC works, the FPU works, the SPI works, some fairly basic code works and we end up with this! Did cheat a little and end up using a lookup table rather than a Taylor series. Since I really don't need the resolution and when you start scratching the surface the Taylor Series is a reasonable amount more mucking around than it appears and to try and run this as fast as possible I pinched some table generation stuff that I used for the LFO a while ago and re-jigged it a little bit. This is about 400Hz and the sample rate is up around 176kHz with a 16 bit resolution. Now need to get the ADC going...

Sunday, August 4, 2013

The spider...


Oh well... What could Possibly go wrong now?
Actually looks like it might work...

Friday, August 2, 2013

Small...


Hmmm... this is the 16 bit DAC that I bought... it is hiding in the shadow of the Evaluation board and as you can see from the 0.1" spacing of the standard DIL pitch are going to make this a challenging bit of work to wire it up... hopefully more successful than earlier in the week...

Thursday, August 1, 2013

Cortex M4


New project! yep another one... Looking at building a Digital VCO, there are a couple of options here; Texas Instruments, Atmel & STMicroelectronics. I am also getting a different TI part that has the the Cortex M4F core which has floating point! Pros & Cons? Well the Atmel board has 1Mbyte of external RAM, which will be really good for my wavetable VCO. The ST chip can boot along at 168MHz. The TI one I am probably the most familiar with... There are other options out there as well, the Frescale parts (was Motorola) have a more accurate ADC but it is still really only about 14 bits really (the trouble with having sensitive analog parts on a digital substrate), the NXP parts are also quite neat in that they can come with multiple cores so one core can be monitoring the ADC values whilst the main core can be doing the calculations... What I hope to end up with is a couple of different VCO's. The wavetable one that gets the samples from an SD Card. A DX Voice one that uses FM and looks like a single voice of my DX7 but the frequency is 1V/octave. A harmonic oscillator that looks a bit like a cross between a Farlight Page 5 and a Buchla 148 Harmonic Oscillator, well at least Mark Verbos's take on it here. I would also like to do another Buchla favorite, the 259, with the whole gamut of dual modulation of phase, frequency, amplitude and timbre... All I need is a little more time...

Wednesday, July 31, 2013

CPLD says No...


Been making a Divider circuit, it is sort of an enhanced MOTM 120/CGS UNI01/Polyfusion Divider. It all went a bit wrong though when the stupid printer made the transfer about 8% smaller... I rather rashly tried to keep going, with some persuasion I had got all the DIL parts in but it was a bridge too far to get the VQ44 package to work reliably. The JTAG programmer did see it but that was about as far as it was going to go... While doing it all I thought of a much easier way than using a CPLD anyway... so i will just jury rig that onto the board to see... the new idea also dispenses with quite a lot of other cruft on the board as well...

Sunday, July 28, 2013

Sockets + Knobs


Got a parcel from  Tayda and it arrived pretty quickly and the bits are certainly cheap. I now keep thinking of extra things I should have put on the order! Anyway hopefully this will make a few panels to sort of get things rattling along. Tried getting a few knobs and the chicken heads are pretty good -- a little smaller than the ones I have used in the past but quite nice. The Davis 1900 clones I am less enthusiastic about; I cannot get the grub screw to grip on the flat of a shaft OR the normal outside...
Posted by Picasa